Tx 889.77 Rx 844.77 Chan 0659 #659
Tx 889.80 Rx 844.80 Chan 0660 #660
Tx 889.83 Rx 844.83 Chan 0661 #661
Tx 889.86 Rx 844.86 Chan 0662 #662
Tx 889.89 Rx 844.89 Chan 0663 #663
Tx 889.92 Rx 844.92 Chan 0664 #664
Tx 889.95 Rx 844.95 Chan 0665 #665
Tx 889.98 Rx 844.98 Chan 0666 #666
Upper Set Part 1 (667-799)
Tower Freq. Mobile Freq. 11xxxx# Channel
Tx 890.01 Rx 845.01 Chan 0667 #667
Tx 890.04 Rx 845.04 Chan 0668 #668
Tx 890.07 Rx 845.07 Chan 0669 #669
Tx 890.10 Rx 845.10 Chan 0670 #670
Tx 890.13 Rx 845.13 Chan 0671 #671
Tx 890.16 Rx 845.16 Chan 0672 #672
Tx 890.19 Rx 845.19 Chan 0673 #673
Tx 890.22 Rx 845.22 Chan 0674 #674
Tx 890.25 Rx 845.25 Chan 0675 #675
Tx 890.28 Rx 845.28 Chan 0676 #676
Tx 890.31 Rx 845.31 Chan 0677 #677
Tx 890.34 Rx 845.34 Chan 0678 #678
Tx 890.37 Rx 845.37 Chan 0679 #679
Tx 890.40 Rx 845.40 Chan 0680 #680
Tx 890.43 Rx 845.43 Chan 0681 #681
Tx 890.46 Rx 845.46 Chan 0682 #682
Tx 890.49 Rx 845.49 Chan 0683 #683
Tx 890.52 Rx 845.52 Chan 0684 #684
Tx 890.55 Rx 845.55 Chan 0685 #685
Tx 890.58 Rx 845.58 Chan 0686 #686
Tx 890.61 Rx 845.61 Chan 0687 #687
Tx 890.64 Rx 845.64 Chan 0688 #688
Tx 890.67 Rx 845.67 Chan 0689 #689
Tx 890.70 Rx 845.70 Chan 0690 #690
Tx 890.73 Rx 845.73 Chan 0691 #691
Tx 890.76 Rx 845.76 Chan 0692 #692
Tx 890.79 Rx 845.79 Chan 0693 #693
Tx 890.82 Rx 845.82 Chan 0694 #694
Tx 890.85 Rx 845.85 Chan 0695 #695
Tx 890.88 Rx 845.88 Chan 0696 #696
Tx 890.91 Rx 845.91 Chan 0697 #697
Tx 890.94 Rx 845.94 Chan 0698 #698
Tx 890.97 Rx 845.97 Chan 0699 #699
Tx 891.00 Rx 846.00 Chan 0700 #700
Tx 891.03 Rx 846.03 Chan 0701 #701
Tx 891.06 Rx 846.06 Chan 0702 #702
Tx 891.09 Rx 846.09 Chan 0703 #703
Tx 891.12 Rx 846.12 Chan 0704 #704
Tx 891.15 Rx 846.15 Chan 0705 #705
Tx 891.18 Rx 846.18 Chan 0706 #706
Tx 891.21 Rx 846.21 Chan 0707 #707
Tx 891.24 Rx 846.24 Chan 0708 #708
Tx 891.27 Rx 846.27 Chan 0709 #709
Tx 891.30 Rx 846.30 Chan 0710 #710
Tx 891.33 Rx 846.33 Chan 0711 #711
Tx 891.36 Rx 846.36 Chan 0712 #712
Tx 891.39 Rx 846.39 Chan 0713 #713
Tx 891.42 Rx 846.42 Chan 0714 #714
Tx 891.45 Rx 846.45 Chan 0715 #715
Tx 891.48 Rx 846.48 Chan 0716 #716
Tx 891.51 Rx 846.51 Chan 0717 #717
Tx 891.54 Rx 846.54 Chan 0718 #718
Tx 891.57 Rx 846.57 Chan 0719 #719
Tx 891.60 Rx 846.60 Chan 0720 #720
Tx 891.63 Rx 846.63 Chan 0721 #721
Tx 891.66 Rx 846.66 Chan 0722 #722
Tx 891.69 Rx 846.69 Chan 0723 #723
Tx 891.72 Rx 846.72 Chan 0724 #724
Tx 891.75 Rx 846.75 Chan 0725 #725
Tx 891.78 Rx 846.78 Chan 0726 #726
Tx 891.81 Rx 846.81 Chan 0727 #727
Tx 891.84 Rx 846.84 Chan 0728 #728
Tx 891.87 Rx 846.87 Chan 0729 #729
Tx 891.90 Rx 846.90 Chan 0730 #730
Tx 891.93 Rx 846.93 Chan 0731 #731
Tx 891.96 Rx 846.96 Chan 0732 #732
Tx 891.99 Rx 846.99 Chan 0733 #733
Tx 892.02 Rx 847.02 Chan 0734 #734
Tx 892.05 Rx 847.05 Chan 0735 #735
Tx 892.08 Rx 847.08 Chan 0736 #736
Tx 892.11 Rx 847.11 Chan 0737 #737
Tx 892.14 Rx 847.14 Chan 0738 #738
Tx 892.17 Rx 847.17 Chan 0739 #739
Tx 892.20 Rx 847.20 Chan 0740 #740
Tx 892.23 Rx 847.23 Chan 0741 #741
Tx 892.26 Rx 847.26 Chan 0742 #742
Tx 892.29 Rx 847.29 Chan 0743 #743
Tx 892.32 Rx 847.32 Chan 0744 #744
Tx 892.35 Rx 847.35 Chan 0745 #745
Tx 892.38 Rx 847.38 Chan 0746 #746
Tx 892.41 Rx 847.41 Chan 0747 #747
Tx 892.44 Rx 847.44 Chan 0748 #748
Tx 892.47 Rx 847.47 Chan 0749 #749
Tx 892.50 Rx 847.50 Chan 0750 #750
Tx 892.53 Rx 847.53 Chan 0751 #751
Tx 892.56 Rx 847.56 Chan 0752 #752
Tx 892.59 Rx 847.59 Chan 0753 #753
Tx 892.62 Rx 847.62 Chan 0754 #754
Tx 892.65 Rx 847.65 Chan 0755 #755
Tx 892.68 Rx 847.68 Chan 0756 #756
Tx 892.71 Rx 847.71 Chan 0757 #757
Tx 892.74 Rx 847.74 Chan 0758 #758
Tx 892.77 Rx 847.77 Chan 0759 #759
Tx 892.80 Rx 847.80 Chan 0760 #760
Tx 892.83 Rx 847.83 Chan 0761 #761
Tx 892.86 Rx 847.86 Chan 0762 #762
Tx 892.89 Rx 847.89 Chan 0763 #763
Tx 892.92 Rx 847.92 Chan 0764 #764
Tx 892.95 Rx 847.95 Chan 0765 #765
Tx 892.98 Rx 847.98 Chan 0766 #766
Tx 893.01 Rx 848.01 Chan 0767 #767
Tx 893.04 Rx 848.04 Chan 0768 #768
Tx 893.07 Rx 848.07 Chan 0769 #769
Tx 893.10 Rx 848.10 Chan 0770 #770
Tx 893.13 Rx 848.13 Chan 0771 #771
Tx 893.16 Rx 848.16 Chan 0772 #772
Tx 893.19 Rx 848.19 Chan 0773 #773
Tx 893.22 Rx 848.22 Chan 0774 #774
Tx 893.25 Rx 848.25 Chan 0775 #775
Tx 893.28 Rx 848.28 Chan 0776 #776
Tx 893.31 Rx 848.31 Chan 0777 #777
Tx 893.34 Rx 848.34 Chan 0778 #778
Tx 893.37 Rx 848.37 Chan 0779 #779
Tx 893.40 Rx 848.40 Chan 0780 #780
Tx 893.43 Rx 848.43 Chan 0781 #781
Tx 893.46 Rx 848.46 Chan 0782 #782
Tx 893.49 Rx 848.49 Chan 0783 #783
Tx 893.52 Rx 848.52 Chan 0784 #784
Tx 893.55 Rx 848.55 Chan 0785 #785
Tx 893.58 Rx 848.58 Chan 0786 #786
Tx 893.61 Rx 848.61 Chan 0787 #787
Tx 893.64 Rx 848.64 Chan 0788 #788
Tx 893.67 Rx 848.67 Chan 0789 #789
Tx 893.70 Rx 848.70 Chan 0790 #790
Tx 893.73 Rx 848.73 Chan 0791 #791
Tx 893.76 Rx 848.76 Chan 0792 #792
Tx 893.79 Rx 848.79 Chan 0793 #793
Tx 893.82 Rx 848.82 Chan 0794 #794
Tx 893.85 Rx 848.85 Chan 0795 #795
Tx 893.88 Rx 848.88 Chan 0796 #796
Tx 893.91 Rx 848.91 Chan 0797 #797
Tx 893.94 Rx 848.94 Chan 0798 #798
Tx 893.97 Rx 848.97 Chan 0799 #799
Upper Set Part 2 (991-1023)
Tower Freq. Mobile Freq. 11xxxx# Channel
Tx 869.04 Rx 824.04 Chan 0991 #800
Tx 869.07 Rx 824.07 Chan 0992 #801
Tx 869.10 Rx 824.10 Chan 0993 #802
Tx 869.13 Rx 824.13 Chan 0994 #803
Tx 869.16 Rx 824.16 Chan 0995 #804
Tx 869.19 Rx 824.19 Chan 0996 #805
Tx 869.22 Rx 824.22 Chan 0997 #806
Tx 869.25 Rx 824.25 Chan 0998 #807
Tx 869.28 Rx 824.28 Chan 0999 #808
Tx 869.31 Rx 824.31 Chan 1000 #809
Tx 869.34 Rx 824.34 Chan 1001 #810
Tx 869.37 Rx 824.37 Chan 1002 #811
Tx 869.40 Rx 824.40 Chan 1003 #812
Tx 869.43 Rx 824.43 Chan 1004 #813
Tx 869.46 Rx 824.46 Chan 1005 #814
Tx 869.49 Rx 824.49 Chan 1006 #815
Tx 869.52 Rx 824.52 Chan 1007 #816
Tx 869.55 Rx 824.55 Chan 1008 #817
Tx 869.58 Rx 824.58 Chan 1009 #818
Tx 869.61 Rx 824.61 Chan 1010 #819
Tx 869.64 Rx 824.64 Chan 1011 #820
Tx 869.67 Rx 824.67 Chan 1012 #821
Tx 869.70 Rx 824.70 Chan 1013 #822
Tx 869.73 Rx 824.73 Chan 1014 #823
Tx 869.76 Rx 824.76 Chan 1015 #824
Tx 869.79 Rx 824.79 Chan 1016 #825
Tx 869.82 Rx 824.82 Chan 1017 #826
Tx 869.85 Rx 824.85 Chan 1018 #827
Tx 869.88 Rx 824.88 Chan 1019 #828
Tx 869.91 Rx 824.91 Chan 1020 #829
Tx 869.94 Rx 824.94 Chan 1021 #830
Tx 869.97 Rx 824.97 Chan 1022 #831
Tx 870.00 Rx 825.00 Chan 1023 #832
----------------------------------------------------------------------------
I got this from a bbs in the (708) are code. It had no name associated
with it. Since NOONE has mailed me any other info on it, I will keep this
in the bible until someone bitches or sends me something tangible.
-ML
MOTOROLA "TRIK-CLIP"
This is the plans I recieved for the Flip. Supposedly if one knew the
pinouts on the other moto phones one could transpose. (maybe!) I never
tested this so I don't know if it works. The chip in the flip the text
is talking about is a 32 pin square plcc
After Phone Disassembly Locate 27c512 Eprom on phone board. This is
On The Upper Right Side Of The Display Next To The Roam Indicator.
This Is a 32 pin Square device. **Note the dot and beveled edge
for pin orientation (the dot is pin 1) Count to the left
counter clock wise 2 3 4 5 and so on. To the Right or clockwise
of the dot is pin 32 Vcc. This will aid you in your count to find
pin 25 which is the eprom output enable. This pin is at ground or
Vss - Level. **Note Pin 25 on Eprom in phone must be lifted from
the phone board ground or Vss state. Use an X-acto Knife and or
soldering iron and tools to cut pin at board level where pin
narrows. Do not bend wide part of pin up on eprom as this could
break off of Eprom. Also Wide Part of pin Will be used to make
contact with eprom test clip adapter. The eprom test clip adapter
will take pin 25 to logic high through an 8 to 10 thousand
resistor to pin 32 Vcc. This will Gate off all data Commands from
the phone board eprom and allow the eprom test clip adaptor to
take over. **Note test clip could touch narrow part of cut off
pin on board and cause phone not to power up please remove or fold
down as low as possible so test clip only touches side of eprom.
After programing is complete put pin 25 back together or find a
suitable ground or Vss - source. The phone will power up and work
without pin 25 put back together but for long term precaution
put back to a logic zero or ground to enable the output enable.
To use the eprom test clip adapter pull the locking wedge on the
test clip into the upper postition. Seat the eprom test clip adapter
onto the eprom in the phone. Make sure to orient the dot and
beveled edge with each other. Push the locking wedge down to lock
the the eprom test clip adapter onto the eprom in the phone. Hook up
the programing cable to the computer and plug into the jack on the
base of the phone. Also hook up the loose lead with a jumper to the
center terminal between the battery contacts. Turn power on green
light on phone display should come on thgen a complete display test
will light up after that the no service will blink along with the
signal level mark in corner of display. If the antenna is still on
the phone it could change to roam or something else. I suggest
remove the antenna so the cell sight will not see you. If you do
not get a power on test with the display there are 3 possible
things (1) pin 25 on phone board is touching the test clip this
can be checked by looking with a volt meter at pin 25 where
resistor connects for 4 to 5 volts pos with reference to ground.
(2) Test clip is not sitting on chip good some times you have pull
the test clip up off of the eprom a 64th of an inch all the way
around. (3) there is corrupt data, Pull the eprom test clip off
Phone check to see if power on display is there.
Computer see if data or phone number or cell sight code or data
whole is ok I've seen the cell sight ID corrrupt and the phone play
dead on the power on test. The test clip sometimes needs
maintenance look at the gold pins.
Make sure all the pins are level with the edge of it. If not take
an X-acto or pin and lightly bend them out so they are along the
edge of the plastic of the test clip.
Always check to see if eprom in phone contacts are clean before
putting test clip on. **Note when test clip is on phone - only
change the ESN only. *The other data phone number lock and so on
can be changed without the test clip and and should be done so.
The software version in the test clip is 9148 you will see this in
the right corner of the computer. Sometimes the program will crash
during the ESN wright this will put all zeros in the ESN field
check the test clip try again. Sometimes I've had to do this 3 an 4
times. Also watch the phone display for codes I've seen at the end
of a wright the code (FO8) just before power down I've had no
problem there but during the key wright (FO8) means i've crashed.
Also during the time when the program is counting back into the
phone i've had (F1O) show up in the display of the phone this
problem means the next time you may not get the power on display
test pull test clip read phone check data to see if cell sight
code is corrupt or some other data correct try again. A word of
caution do not push on eprom on top of test clip as this could
seat eprom lower into adapter and cause bad contact. To remove
test clip pull locking wedge up to unlock the eprom test clip
adapter from the eprom in the phone. Continue pulling up to lift
the eprom test clip adapter from the eprom in the phone.
-----------------------------------------------------------------------------
DISCLAIMER: I, Mike Larsen, accept NO responsibility for people using any
info within this text for fraudulant purposes. I did not intend for the info to be used towards fraud or theft of services. The main reason I spent hundreds of hours creating and compiling this information is because programming fees are BULLSHIT and they know it. If you notice, the 37#
command is no longer a mystery and Motorola is quite pissed I found out. I "engineered" it from a floor manager or some other head at the Motorola cellular division. "Big Deal" you say. Well, Motorola shipped Many flip
fones with that command set for a different battery. After 10 minutes of use the phone would die. The phone had to be sent to Motorola to be "fixed."
If you found this text useful, please mail something interesting or just let me know you appreciated my efforts. You can't believe how pissed
I was when I found out some lamer is changing the name in the text to his
own so people will like him or something. Have fun.
Oh, by the way, I forgot to mention in the above disclaimer that I do
nothing fraudulant with MY fone. I pay a bill and everything and can prove it. So will the "feds" or whoever the Internet gestapo is that's been sending me mail about me being under thier "watchful eye", please go for someone else that's dealing child pornography or asking for WaReZ? Thanks.
Mike.Larsen@uti.com
stularsenmic@vax.colsf.edu
------------------------------------------------------------------------------
--- Mystic BBS v1.12 A43 (Linux/32)
* Origin: HAMRADIO telnet lu9dce.dynu.com (21:5/101)