• Rotator Yaesu G250 info

    From G8MNY@21:5/101 to TECH on Thu Jul 11 03:10:35 2019
    R:190711/0605z @:VE3CGR.#SCON.ON.CAN.NOAM [Aurora] jnos2.0k.3B #:4674 $:12000_G R:190711/0604z @:I0OJJ.ITA.EU [Rome] #:21789 $:12000_GB7CIP
    R:190711/0604z @:IZ3LSV.IVEN.ITA.EU $:12000_GB7CIP
    R:190711/0604z @:F1OYP.FAQI.FRA.EU $:12000_GB7CIP
    R:190711/0504z @:ON0AR.#AN.BEL.EU $:12000_GB7CIP
    R:190711/0604Z @:GB7CIP.#32.GBR.EURO #:12000 [Caterham Surrey GBR]

    From g8mny%gb7cip.#32.gbr.euro@i0ojj.ampr.org Thu Jul 11 08:04:18 2019 Received: from i0ojj.ampr.org by i0ojj.ampr.org (JNOS2.0k.3b) with SMTP
    id AA21789 ; Thu, 11 Jul 2019 08:04:18 +0200
    Message-Id: <12000_GB7CIP@iz3lsv.bbs>
    From: g8mny@gb7cip.#32.gbr.euro
    X-JNOS-User-Port: Uplink (IZ3LSV-8 on port hub) -> Sending message

    From: G8MNY@GB7CIP.#32.GBR.EURO
    To : TECH@WW

    By G8MNY (New Jan 06)
    (8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

    This is small basic & reliable rotator with pot control & self hunting etc.
    _
    ==║]│ Small Dia Stub
    ____________________________ ║ │ Pole Clamps
    / ___ _ _ / │ ==║]│
    / / _ \ __ / │ ┌─────╨─┴───┐
    / │ (_) │ / / / │ 6 Wire _│___________│_ ROTATOR
    \___ / /_/ / │ Cable │___________│
    /_ _ _ _ _ _ _ _ _ _ _ _ _ / _.┘ ===║]|│ - - option flat │__________________________│_.-' ║ |│ base plate
    CONTROLLER Support U ===║]|│ remove bolts
    Mast Clamps ╙─┴┘

    DIAGRAM
    N─o/'o─┐ ┌─────┬──────────────────────────────────────────*6*───────┐
    )║( └─┤<├──────2k2──┤<├─┐ AC Common \ Thermal
    240V )║( RUN// CW │ │ Trip
    )║( 24V LED ┌─o\────┬──────┴──────────────────────*5*─())))─┤
    )║( │ === 68uF 60v AC ===== │MOTOR
    )║ └──────────┴─o/────┴─────────────────────────────*4*─())))─┘
    │ ║ CCW
    o ║ ┌─────┬─┤>├─┬──┬──────┬─────120Ω──┬────┬─────────────┐
    FUSE | ║(12V _│_ │ R ┌───┴───┐ _│_ │ +10V Cal1\│/
    o ║(___ /_\ │ │ │ C W │ 10V/_\' │ ┌─3k──*1*──┐ L─o/'o─┘ ║( │ │ +16V│ _│_ └───┬───┘ │ │ │ │
    on/off ║(12V│ │ │ \_/≡ ├──┐NPN │ 7│ 3 HEADING │
    │ ├──)──)─┤>├─┤ │ON _│_ \│__ │ 741/├──((()─>POT │ E────────┘_│_ │ │ │ │ /_\ e/│ ├─R─)──<' │± 200Ω ROTATOR
    /_\ └──)─────)──┴─────┬┴─┬┴────)───┤ 2 `\├──((()───)────*2*─>POT
    │ │ +│ _│_ e\│___│ │ 4│ 2 RFC │ 200Ω
    │ │ === /_\ /│ │ │ │ │
    │ │ 100u│ ├──┘PNP │ │ └─3k──*3*──┘
    │ │ │ ┌───┴───┐ _│_ │ Cal2 /│\
    │ │ -16V│ │ C C W │ 10V /_\' │ │
    │ │ │ └───┬───┘ │ │ -10V │
    └─────┴─────┴────────┴──────120Ω──┴────┴─────────────┘
    (N.B. Incomplete diagram) * External Connections

    DESCRIPTION
    Two relays power the 2 pole AC rotator motor on either line 4 or 5. The Run LED is lit when either is powered as either 24V AC or via the phase shift AC capacitor. The relays are operated by the opamp & either driver transistor. The opamp inputs are feed via RF filtering components with the bridge output, comparing the slider voltage of the controller & rotator pots. The cal presets enable calibration of ±180° positions (south).

    IN USE
    Although a very small rototor, I have used an enoumous 55el 23cms TONNA beam 5.5m long on one at 10m for many years. But to keep bearing strain down I use only a 3cm x 30cm long stub pole.


    Why Don't U send an interesting Bul?

    73 de John G8MNY @ GB7CIP



    --- Mystic BBS v1.12 A43 (Linux/32)
    * Origin: HAMRADIO telnet lu9dce.dynu.com (21:5/101)